Fire Pump Inspection
Visual and operational inspection to identify defects, abnormal conditions and maintenance requirements.
- Pump and motor condition
- Suction and discharge piping
- Valves, gauges and accessories
Fire Protection System Services
Fire Pump Testing,
Servicing & Maintenance
Professional fire pump inspection, performance testing, preventive maintenance and troubleshooting for commercial, industrial and residential fire protection systems in Bangladesh.
Inspection & Testing
Preventive Maintenance
Technical Service Support
Fire Pump Reliability Starts with Proper Maintenance
Inspection • Testing • Servicing • Documentation
About Our Service
Keep Your Fire Pump System Ready for Emergency Operation
A fire pump is a critical component of a water-based fire protection system. Its performance can be affected by mechanical wear, electrical faults, controller issues, fuel problems, suction restrictions and inadequate maintenance.
AJ Fire Safety & Engineering Solutions provides fire pump inspection, testing, servicing and maintenance support based on site conditions, equipment specifications, manufacturer recommendations and applicable fire protection requirements.
- ✓ Electric motor-driven fire pump inspection and service
- ✓ Diesel engine-driven fire pump inspection and service
- ✓ Jockey pump and controller inspection
- ✓ Performance test records and maintenance recommendations
Our Technical Services
Complete Fire Pump Testing & Servicing Solutions
Service activities are selected according to the installed equipment, system design, operating condition and agreed scope.
Fire Pump Performance Testing
Assessment of operating conditions and measured performance against the approved pump curve and applicable acceptance criteria.
- Flow and pressure readings
- Operating condition assessment
- Test data documentation
Preventive Maintenance
Planned servicing intended to identify developing problems and support dependable equipment operation.
- Routine condition checks
- Lubrication where specified
- Maintenance planning
Fire Pump Repair & Troubleshooting
Technical investigation of reported faults and recommendations for corrective action.
- Abnormal vibration or noise
- Pressure and starting problems
- Mechanical or electrical fault assessment
Controller & Electrical Checks
Inspection of pump controllers and associated electrical components within the agreed service scope.
- Controller indication and alarms
- Starting and control functions
- Electrical connections and condition
AMC & Scheduled Maintenance
Planned service arrangements for facilities requiring periodic fire pump system inspection and maintenance.
- Scheduled site visits
- Service reports and observations
- Recommendations for corrective work
Equipment Coverage
Fire Pump Systems We Can Assess
Contact our team to confirm service availability for your specific pump make, model, capacity and installation.
Electric Fire Pump
Inspection of electric motor-driven fire pumps, motor condition, pump operation, controller functions and associated components.
Diesel Engine Fire Pump
Assessment of engine starting, fuel and cooling systems, battery condition, lubrication and pump operation, as applicable to the equipment.
Jockey Pump
Inspection of pressure-maintenance pump operation, pressure settings, starting and stopping behaviour, and related control components.
Maintenance Checklist
Key Inspection & Testing Activities
The final checklist depends on the equipment, system design, approved procedures and applicable testing requirements.
Mechanical Inspection
- Pump casing and visible leakage
- Coupling and alignment condition, where applicable
- Foundation, mounting and vibration observations
- Suction and discharge valve condition
- Bearings and lubrication requirements
Operational Testing
- Starting and stopping functions
- Pressure gauge readings
- Flow measurements using an approved method
- Operating data compared with pump performance data
- Abnormal noise, vibration or temperature observations
Diesel & Electrical Checks
- Battery and charging system condition
- Fuel, cooling and lubrication checks
- Controller status and fault indications
- Electrical supply and connections
- Alarms and control functions, as applicable
Testing must be planned and performed by competent personnel using suitable instruments and safe procedures. Do not operate equipment outside its approved operating limits.
Our Work Process
From Initial Assessment to Service Report
A structured approach helps document equipment condition, test findings and recommended follow-up actions.
Site Assessment
Review pump details, system configuration, reported problems, available records and site requirements.
Inspection & Testing
Carry out the agreed inspection and testing procedures with appropriate safety precautions and instruments.
Findings & Recommendations
Record observed conditions, measurements, deficiencies and recommended corrective or preventive actions.
Service Planning
Discuss necessary repairs, follow-up work and a suitable maintenance schedule with the client.
Standards & Best Practice
Testing Based on Applicable Requirements
Fire pump testing and maintenance should be planned according to the applicable standard edition, approved system design, manufacturer instructions, authority requirements and site-specific procedures.
NFPA 20
Standard for the Installation of Stationary Pumps for Fire Protection.
NFPA 25
Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems.
Manufacturer Instructions
Equipment-specific operating and maintenance requirements.
Local Requirements
Applicable Bangladesh regulations and authority requirements.
Reference to NFPA standards does not constitute NFPA certification, approval or endorsement of AJ Fire Safety & Engineering Solutions. The applicable edition and requirements must be verified for each project.
Industries We Serve
Fire Pump Maintenance for Different Facilities
Service requirements are assessed according to the facility's risk profile, installed fire protection system and operational needs.
Garments & Textile
Factory fire protection systems
Industrial Facilities
Manufacturing and processing plants
Commercial Buildings
Offices and business premises
Warehouses
Storage and distribution facilities
Shopping Complexes
Retail and mixed-use buildings
Hospitals & Clinics
Healthcare facility fire protection
Hotels & Hospitality
Guest and service facilities
Residential Buildings
Applicable shared fire pump systems
Frequently Asked Questions
Fire Pump Testing & Servicing FAQs
Answers to common questions about fire pump inspection, performance testing and maintenance planning.
Why is regular fire pump testing important?
Regular testing helps assess equipment readiness, operating pressure, flow performance, controller operation and associated equipment condition. It can also help identify deficiencies before an emergency. Follow the applicable standard, approved procedures and manufacturer's instructions.
How often should a fire pump be tested?
Testing frequency depends on the applicable edition of NFPA 25 or other governing requirements, pump type, installation, manufacturer instructions and authority requirements. The site's responsible fire protection professional should establish the required schedule.
Can you service diesel and electric fire pumps?
Service requirements can cover electric motor-driven fire pumps, diesel engine-driven fire pumps, jockey pumps and associated controllers. Confirm the installed equipment details and required scope with our team before scheduling a visit.
Do you provide fire pump performance test reports?
Test documentation can be discussed as part of the agreed service scope. Records may include equipment details, operating readings, observed deficiencies and recommendations, depending on the test performed.
Do you offer an Annual Maintenance Contract (AMC)?
You can contact AJ Fire Safety & Engineering Solutions to discuss a scheduled maintenance plan or AMC. The proposal can be prepared according to the number and type of pumps, site location, required visits and agreed service coverage.
Which information should I provide to request a quotation?
Please share the site location, pump manufacturer and model, rated flow and pressure, pump driver type, number of pumps, reported problems and preferred service date. Photos of the nameplate and pump room may help with the initial assessment.
Contact Our Technical Team
Need Fire Pump Testing, Servicing or Maintenance?
Contact AJ Fire Safety & Engineering Solutions to discuss your fire pump system, inspection requirements, corrective maintenance or AMC proposal.
AJ FIRE SAFETY & ENGINEERING SOLUTIONS — Your Trusted Fire Safety & Engineering Solution Partner. Service scope, availability, testing procedures and quotations are subject to site assessment and written agreement.
